Whelen 70509 Flasher Uživatelský manuál stáhnout pdf

Page 1

ENGINEERING COMPANY INC.

Route 145, Winthrop Road,

Chester, Connecticut 06412

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: aviation@whelen.com

Aviation

Installation Guide

Model 70509 Flasher

Form No.13215C (041202)

Model 70509

Flasher

TSO-C96A

Approved

EQUIPMENT LIMITATIONS

The Model 70509 Flasher meets the requirements of

FAR 23.1401 and 25.1401. “If certification for night

operations is requested, the airplane must have an

anti-collision light system that consists of one or more

approved anti-collision lights located so that their light

will not impair the flight crew members vision or detract

from the conspicuity of the position lights.”

OPERATING INSTRUCTIONS

14V INPUT VOLTAGE14V

UNIT INPUT CURRENT(LAMP ON)2.7 AMPS

INPUT CURRENT(AVERAGE)1.3 AMPS

28V INPUT VOLTAGE 28V

UNIT INPUT CURRENT(LAMP ON)1.3 AMPS

INPUT CURRENT(AVERAGE).65 AMPS

FLASH RATE 50 ±5 FPM

LAMP 35W HALOGEN

DUTY CYCLE 50%

INSTALLATION PROCEDURES

The following information is to assist you in installing a

Whelen flashing anti-collision light system.

1. Choose an appropriate Model 70509 flashing anti-

collision light assembly (14V or 28V) which is

applicable to your aircraft.

2. The installation procedure described in the

following text will be confined to a single light

installation, but is identical for multiple light

installation if required.

3. Remove old anti-collision light and flasher

assembly. Locate and save existing applicable

+14VDC or +28VDC lead and (-) ground lead.

Clean and prep lead ends as required.

4. Connect existing +14VDC or +28 VDC lead to the

(red or white) lead on the light assembly and

connect existing (-) ground lead to the (black) lead

on the light assembly. Both leads must be

connected by an approved aircraft connection.

5. Breaker Requirements

14VDC

System - Make sure existing system is

equipped with a maximum 5 amp breaker for one

light and a maximum 10 amp breaker for a two

light system.

28VDC

System - Make sure existing system is

equipped with a maximum 2.5 amp breaker for

one light and a maximum 5 amp breaker for a two

light system.

6. Install light assembly and insure that all leads are

clear of any obstructions. Secure light assembly,

use lock washers and/or thread locker on all

threaded fasteners.

7. Check all avionics systems for interference from

this installation.

8. When necessary, waterproof the flasher base

assembly to aircraft. Apply single part silicone

(RTV) or equivalent around any open area where

water could get in.

9. Update aircraft records and complete Form 337.

10. Obtain FAA field approval for installation.

1 2

Shrnutí obsahu

Strany 1 - Aviation

Page 1®ENGINEERING COMPANY INC.Route 145, Winthrop Road,Chester, Connecticut 06412Phone: (860) 526-9504Fax: (860) 526-2009Internet: www.whelen.comSale

Strany 2 - MODEL 70509 REPLACEMENT PARTS

Page 2MODEL 70509DIMENSIONSFLASHERS /MOUNTING BASEASSEMBLYLABEL(REF)(+28V) WHITE(14V) REDBLACK (-)}261920CLAMPRINGLENSASSEMBLY3.702.586.00±.5098721810

Komentáře k této Příručce

Žádné komentáře

Whelen 70509 Flasher Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Vzduchová zařízení Whelen 70509 Flasher. Whelen 70509 Flasher User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Vzduchová zařízení Whelen 70509 Flasher