Whelen 7108001 Uživatelský manuál stáhnout pdf

Page 1

2.60

3.74

(-) GROUND

BLACK

18AWG

12.0” ±1.0” (-01)

24.0” ±1.0” (-06)

(+) 28VDC

WHITE

18AWG

12.0” ±1.0” (-01)

24.0” ±1.0” (-06)

ENGINEERING COMPANY INC.

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-2009

Internet: www.whelen.com

Sales/Service e-mail: [email protected]

Aviation

Installation Guide:

Model 71080( )-series

Model(s) 7108001, 7108006

P/N(s):01-0771080-01

01-0771080-06

LED Flashing Anti-Collision

Light Assembly

Form No.14162C (060314)

OPERATING INSTRUCTIONS:

Operational Voltage: . . . . . . . . . . . 28 VDC nominal

(Operational from 22VDC to 30VDC)

Average Input Current: . . . . . . . . . 0.45 Amps

Peak Input Current:. . . . . . . . . . . . 2.0 @ .3 Seconds

The Model 71080 series LED anti-collision light assembly meets the

requirements of FAR 91.205(c)(3).

EQUIPMENT LIMITATIONS: An approved anti-collision light assembly should be

located so that the light will not impair the crew’s vision or detract from the

conspicuity of the position lights. The baseplate must be mounted parallel to the

vertical and horizontal centerlines of the aircraft to project the patterns properly.

Certain types of installations may require additional testing.

CONTINUED AIRWORTHINESS: The 71080 series LED anti-collision light

assembly is designed with 8 vertical columns consisting of 4 LEDs each. Should any

one LED or any vertical column fail, the unit must be repaired or replaced. Inspect

the lens and replace if there is excessive scratching, discoloration or cracking.

NOTE: To reduce eye strain, use an optical filter such as dark glasses or a blue

covering dome during LED inspection.

INSTALLATION PROCEDURES: The following information is to assist in the

installation of a Whelen LED Anti-collision Light System.

1. Using the mounting detail information provided, prepare the aircraft for means

to secure the light assembly.

2. Carefully remove the #4 Phillips screw and lens retainer. Remove the lens.

CAUTION! Do not touch the LEDs with either fingers or sharp objects. This

could soil and/or damage the LED and effect the optical performance of the

LEDs. Remove the 4 Phillips head screws securing the adapter plate to the

light assembly. Remove the adapter.

3. Using the appropriate hardware, install the adapter plate to the aircraft.

4. Route the wires through the opening in the adapter plate. Connect the light

inputs according to the chart shown. Connect the power lead to an

appropriately sized breaker. Connections to be in accordance with FAA

approved methods.

5. Reinstall the light assembly onto the adapter plate and insure that all leads are

clear of any obstructions and secured as required.

6. Install gasket, lens and lens retainer. Confirm proper gasket fit. Reinsert screws

and tighten firmly.

7. All inverted (bottom) mounted units shall require waterproofing of the base

assembly to the aircraft. NOTE: Drill a 1/8” hole in the center of the lens for

bottom mount units.

8. Check all avionics systems for interference from this installation.

9. A flight check should be performed by a properly certified pilot.

10. Update aircraft records, complete Form 337 and obtain FAA field approval for

installation, as required.

MADE IN THE U.S.A.

The conditions and tests required for TSO approval of this article are minimum

performance standards. It is the responsibility of those installing this article either on

or within a specific type or class of aircraft to determine that the aircraft installation

conditions are within the TSO standards. TSO articles must have separate approval

for installation in aircraft. The article may be installed only if performed under 14 CFR

part 43 or the applicable airworthiness requirements.

TSO-C96a

CLASS I, III;

APPROVED

1 2

Shrnutí obsahu

Strany 1 - Aviation

Page 12.603.74(-) GROUNDBLACK18AWG12.0” ±1.0” (-01)24.0” ±1.0” (-06)(+) 28VDCWHITE18AWG12.0” ±1.0” (-01)24.0” ±1.0” (-06)®ENGINEERING COMPANY INC.51 W

Strany 2 - ITEM PART NUMBER DESCRIPTION

Page 21263 4578910114 x #6-32 MTG holesequally spaced ona 1.750 bolt circle4 x #6-32 MTG holesequally spaced ona 1.625 bolt circle4 x #6-32 MTG hole

Příbuzné modely 7108006 | 7118400 | 7118401 | 7108040 | 7117001 | 7117002 | 7117007 | 7117008 | 7117009 | 7117010 | 7108019 | 9027701 | 9027702 | 7105000 | 9052008 |

Komentáře k této Příručce

Žádné komentáře

Whelen 7108001 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Vzduchová zařízení Whelen 7108001. Whelen 7108001 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 7108006 | 7118400 | 7118401 | 7108040 | 7117001 | 7117002 | 7117007 | 7117008 | 7117009 | 7117010 | 7108019 | 9027701 | 9027702 | 7105000 | 9052008 |

Komentáře k této Příručce

Související produkty a manuály pro Vzduchová zařízení Whelen 7108001